Shop NICE NORTH AMERICA | Brands We Sell

Duplicate product

The 2GIG-FT1-345 is a wireless flood and temperature sensor for 2GIG control panels. The 2GIG-FT1-345 is the perfect sensor to alert the home owner of a flood or excessive change in temperature. The 2GIG-FT1-345 is a fully supervised, tamper protected one-way 345 MHz sensor. It will monitor the ambient temperature of a space for high and low temperature thresholds and report changes outside of the defined settings. The FT1-345 also has the ability to detect and report wet/dry flood condition in the event of the presence of standing water in the immediate sensor location. The FT1-345 sensor reports wet/dry conditions and temperature to the panel.

To protect against flood conditions, simply mount the 2GIG-FT1-345 sensor near a home’s water heater or other contained water source and mount the sensor probe slightly above the floor. If a substantial leak occurs, the water will complete the circuit between the two probes on the sensor and a flood trouble or alarm will be sent to the panel.

Ensure your 2GIG EDGE Security Panel is always online with the 2GIG EDGE Panel Replacement Backup Battery. This replacement backup power supply is designed specifically for the 2GIG-EDG-NA-AA and 2GIG-EDG-NA-VA Security Panels and keeps them active when their main power supply is offline or disconnected. The Backup Battery charges through its connected EDGE Security Panels while they are being regularly powered. The 2GIG EDGE Panel Replacement Backup Battery can keep the 2GIG Edge System operational for approximately 24 hours. The battery has an expected lifespan of at least five (5) years.

The PD300EMZ5-1 Plug-in Lamp Module is designed to provide Z-Wave control to a connected dimmable lamp. The PD300EMZ5-1 module is plugged into any standard grounded AC wall outlet, and the lamp is then plugged into the module. Once connected, the lamp can be dimmed or turned on or off remotely via the Z-Wave controller. The module contains two power receptacles – one controlled, and one pass-through (powered at all times).

The sealed environment 212SE style keypad features a brushed metal housing that has been treated to resist corrosion and an all metal Braille, alpha-numeric keypad. There is an internal sounder that is used to indicate key press feedback, and a bi-color LED to indicate operation. The housing has been designed to mount directly on a standard single-gang electrical box, or to most flat surfaces.

The E+ Smoke/Heat/Freeze Detector – an exciting photoelectric smoke detection solution for dealers in search of the ultimate safety enhancement. Detecting both fixed temperature and rate-of-rise heat, it’s advanced One Go / All Go protocol seamlessly interconnects smoke detectors, ensuring that when one is triggered, all connected E+ Smoke Detectors will sound the alarm. This not only boosts overall safety but also creates a heightened sense of urgency during emergencies.

The 2GIG-CP-DESK Go!Control Desktop Kit allows your 2GIG GC2 control panel to sit at two different viewing angles. Bumper pads on the equipment protect furniture and prevent sliding. Works with any 2GIG GC2 Go!Control panel.
Product Features:
Allows panel to sit at two different viewing angles.
Sleek form factor
. Bumper pads to protect furniture & prevent sliding.
Works with any Go!Control panel

The 2GIG-CO8e-345 is a wireless eSeries encrypted carbon monoxide detector that is designed for indoor use, to detect the presence of CO gas. If deadly CO gas is detected, the 2GIG-CO8e-345 communicates an alarm initiating signal to your 2GIG GC2e, GC3e or EDGE security control panel. Tricolored LED (green, yellow, red) and a sounder on the detector provide local visual and audible indication of the CO8e-345 detector’s status. The carbon monoxide detector is battery operated with a low battery sensor, and an end-of-life notification. Likewise, this device also contains an 85 dBA sounder, as well as a hush/test button for trouble shooting purposes.

High efficiency switching power supply
120 VAC @ 60 Hz input
14 VDC @ 1700 mA output
Screw terminals for wiring connecting to the Control Panel
Includes retaining bracket for standard and Decora style outlets
For use with GC2 or GC3 panels

Allows panel to sit at two different viewing angles, with sleek form factor, including bumper pads to protect furniture and prevent sliding.
Works with the 2GIG EDGE panel and the 2GIG EDGE Remote Keypad.