Shop Intrusion Accessories

The ELK-999 contains 130 pieces of double faced 1/4” thick closed cell foam tape with an aggressive pressure sensitive permanent adhesive on both sides. This tape can be used in place of mechanical fasteners to mount relays, siren drivers, and many other devices to various surfaces. It is flexible and conforms to irregular surfaces.

The ELK-M1XEP is an Ethernet Appliance with a RS-232 Serial Port Interface. It may be used to connect a control in the M1 Family to an Ethernet network. It features email event notification and FIPS compliant encryption algorithms for security sensitive environments. It is powered by an ELK-P1216 12 Volts DC, 1.5 Amp plug-in power supply/adapter. A software setup utility is built into ElkRP for configuring the connection setup, network password, etc. The M1 Ethernet Interface is factory defaulted to obtain a dynamic IP address from a DHCP server (i.e. router, cable modem, etc.). It may optionally be setup with a static IP address.

Adds 16 hardwired zones (EOL resistor supervised) to the M1 Gold or M1EZ8 Controls. Operates from 4-wire data bus. Up to 12 of these can be used, increasing total zones (inputs) to 208.

The ELK-965 is a Low Battery Cutoff Module combined with a Master Power Switch. It is designed to work with virtually any 12 Volt control panel or power supply.
In the event of an extended power outage, the ELK-965 sensing circuit automatically disconnects the battery when the voltage falls below 10 Volts DC. This helps to prevent “deep discharging” of the battery. The convenient power switch permits the installer or user to easily disconnect both the Battery and the AC power from the control or power supply.

An “active” RS-485 data bus hub designed for jobs where an M1Gold or M1EZ8 Control is retrofitting an older panel that has multiple homerun 4 conductor keypad/data wires. It splits the main 485 data bus into 4 managed 485 branches. Each branch can have 2 parallel home run cables for a total of 8 home runs. The end of each cable is EOL terminated to insure proper operation and supervision.

Double Sided Mounting Tape with an aggressive pressure sensitive permanent adhesive on both sides. Package contains an assortment of three (3) thicknesses; 1/16”, 1/8”, and 1/4”. This tape can be used in place of mechanical fasteners to mount relays, siren drivers, and many other devices to various surfaces. It is flexible and conforms to irregular surfaces.

Holds up to an 8 Ah Battery.

Multi-purpose cabinet for structured wiring, controls, & peripherals. Versatile mounting for multiple manufacturer’s structured wiring modules; such as Leviton, OnQ, OpenHouse, and others. May be flush or surface mounted. Flush mounting is ideal for hollow frame walls with studs on 16” centers. The minimum rough opening is 14.25” wide, 28.25” high, 4.5” deep. Can be adjusted for varying wall finish thicknesses and the locking, removable hinged lid extends beyond the box edges approximately 5/8” which easily conceals uneven cutouts of the wallboard edges. It’s universal design features a hole-slot-hole mounting system that allows it to accommodate shelves, brackets, wire modules and equipment from many different manufacturers.
Also see the ELK-SWB14, a smaller 14.25” structured wiring / control box.

The ELK-BLT Battery Life Tester or .Mhos Meter. is a compact, easy to use service tool for testing 12 Volt rechargeable batteries. The BLT measures internal conductivity (Mhos), which is the best indicator of a battery’s health and life expectancy. Mhos happens to be the inverse of Ohms (conductance as opposed to resistance). The BLT operates as follows: For each battery brand and size installed you should start by measuring and recording a .baseline. Mhos reading. Then, during any service call or inspection simply measure and record the current (most recent) Mhos reading. Always compare the current Mhos reading with the original reading.

The ELK-SWB14 is a universal structured wiring box featuring a pattern of hole-slot-hole that allows it to accommodate accessories, circuit boards, shelves, brackets, and wiring modules from many different manufacturers. It is designed to be surface mounted but can be flush mounted with the addition of an optional ELK-SWFD14 Flush Mount Door.